Machined hexagon head bolt made by HAGUE FASTENERS

Materials · Hastelloy

Hastelloy C4 fasteners

HAGUE FASTENERS makes Hastelloy C4 fasteners to order: bolts, studs, nuts and machined parts in Hastelloy C4, the nickel-chromium-molybdenum alloy that stays stable after welding and high temperature exposure, made to your drawing in Willenhall.

Ni-Cr-Mo

Nickel-chromium-molybdenum alloy

As welded

Resists grain boundary precipitates in the weld zone

3.1 / 3.2

EN 10204 certificates with full traceability

1 to 500

Prototypes to batches of several hundred

About the alloy

Corrosion resistance that survives welding

HAGUE FASTENERS makes Hastelloy C4 fasteners in the UK for chemical process equipment that is welded or exposed to high temperatures during fabrication or service. C4 is a nickel-chromium-molybdenum alloy with low carbon and silicon, so it resists the grain boundary precipitates that can leave other alloys open to intergranular attack.

It handles a wide range of process media, from strong oxidisers and chlorine to formic and acetic acids, seawater and brine. For the widest resistance in fully annealed parts, see also C276 and C22.

At a glance

  • Nickel-chromium-molybdenum alloy, nickel balance
  • Suitable for most chemical process duty in the as-welded condition
  • Resists strong oxidisers, chlorine and contaminated acids
  • Bar from UK, EU or US mills with certificates

Composition

Hastelloy C4 chemical composition

Percentage by weight, to UNS N06455 as specified in ASTM B574. Mechanical properties are certified to the specification you order against, on EN 10204 3.1 or 3.2 certificates.

Element Min % Max %
Nickel (Ni) Bal. –
Chromium (Cr) 14.00 18.00
Molybdenum (Mo) 14.00 17.00
Iron (Fe) – 3.00
Cobalt (Co) – 2.00
Titanium (Ti) – 0.70
Manganese (Mn) – 1.00
Silicon (Si) – 0.08
Carbon (C) – 0.015
Phosphorus (P) – 0.04
Sulphur (S) – 0.03

This data is for general information only and may change without notice. HAGUE FASTENERS LIMITED believes it to be accurate but gives no warranty as to its accuracy or completeness and accepts no liability for its use. Actual properties may vary, and nothing here guarantees suitability for a particular use.

Equivalents and applications

Hastelloy C4 equivalents and typical uses

Alternative designations

Hastelloy C-4, Alloy C-4, UNS N06455, W.Nr 2.4610, NiMo16Cr16Ti, ASTM B574 (bar), ASTM B575 (plate, sheet and strip), ASTM B622 (seamless pipe and tube).

Typical applications

  • Welded chemical process equipment
  • Ferric and cupric chloride service
  • Chlorine and contaminated acid streams
  • Formic and acetic acid, acetic anhydride
  • Seawater and brine

What we make

Fasteners we make in Hastelloy C4

Certification and testing

Certified, traceable and tested

Bar comes from approved UK, EU or US mills, with heat numbers carried through to release. Testing is by independent UKAS-accredited laboratories, with EN 10204 3.1 or 3.2 certificates as required. See quality and testing.

  • Mill certificates and heat traceability
  • PMI and chemical analysis
  • Solution annealing by approved partners, with furnace charts
  • Laser-marked heat codes or part numbers
Bars marked with ident, cast and batch number before cutting

Questions

Frequently asked questions

What are Hastelloy C4 fasteners used for?

Hastelloy C4 fasteners are used in chemical process plant, especially welded equipment, where the alloy must keep its corrosion resistance after welding or high temperature exposure.

Why choose Hastelloy C4 over C276?

C4 is chosen for its thermal stability. It resists the grain boundary precipitates that can form in the weld heat-affected zone, so it suits parts used as welded or exposed to high temperatures.

Can you make Hastelloy C4 studs and nuts as sets?

Yes. We make studs, bolts, nuts and washers in matching material and heat, with certificates for each item.

Do you supply Hastelloy C4 with 3.1 certificates?

Yes. We supply EN 10204 3.1 or 3.2 certificates, with PMI and independent test reports where required.

Hastelloy C4 enquiry?

Send us your drawing or specification

Tell us the sizes, quantity and documentation you need, and we will reply quickly.