
Materials · Titanium alloys
Titanium fasteners
HAGUE FASTENERS makes titanium fasteners to order in the UK: bolts, studs, nuts and machined parts in titanium Grade 2, Grade 5 and Grade 7, from certified, traceable bar, for marine, chemical, defence and weight-critical duty.
3 grades
Grade 2, Grade 5 and Grade 7
1 to 500
Single prototypes to batches of several hundred
3.1 / 3.2
EN 10204 certificates with full traceability
UK, EU, US
Mill origin of every bar we use
Why titanium
Light, strong and very corrosion resistant
Titanium fasteners combine high strength with much lower weight than steel, and they are highly resistant to seawater, chlorides and many oxidising chemicals. That makes titanium a natural choice for marine and offshore hardware, chemical plant, defence equipment and anywhere weight matters.
Commercially pure grades such as Grade 2 give the best formability and corrosion resistance; alloyed Grade 5 (Ti-6Al-4V) gives much higher strength; and Grade 7 adds palladium for better resistance to crevice corrosion. HAGUE FASTENERS machines and threads all three.

Grades
Titanium grades we machine
Select a grade for its composition, properties and equivalent designations. The grade supplied always follows your specification.

Titanium Grade 2
Unalloyed, commercially pure (CP) titanium with excellent corrosion resistance and formability.

Titanium Grade 5
Ti-6Al-4V alloy: the high strength titanium grade most used for fasteners.

Titanium Grade 7
Like Grade 2 with added palladium for enhanced crevice corrosion resistance.
Choosing a grade
Matching the grade to the duty
Typical selections only. Where strength at temperature matters more than weight, consider Inconel; for seawater bolting at lower cost, super duplex or Monel.
| Service environment | Grades usually considered |
|---|---|
| High strength, weight-critical bolting | Grade 5 |
| Seawater and marine hardware | Grade 2, Grade 5 |
| Chemical process, crevice corrosion risk | Grade 7 |
| Washers, spacers and lightly loaded parts | Grade 2 |
| Defence and specialist equipment | Grade 5 |
What we make
Titanium fasteners and components
Studs and studbolts
Stud bolts, engineer studs, waisted studs and tie bars
Bolts and screws
Hexagon, 12-point, fitted and special head bolts
Nuts
Hex, heavy hex, jam, flange and special nuts
Washers
Plain, machined, spherical and tab washers
Socket screws
Non-standard cap, set, shoulder and countersunk screws
Turned and milled parts
Plugs, pins, bushes and components to drawing
Proving the material
Certified from mill to final release
Every bar comes from an approved UK, EU or US mill with its certificate, and the heat number is carried through to release. PMI and chemical analysis confirm the grade where specified, and independent UKAS-accredited testing and EN 10204 3.1 or 3.2 certificates are supplied as your order requires. See quality and testing. Titanium threads can gall, so we can advise on anti-seize or coatings where needed.
- Mill certificates and heat traceability
- PMI and chemical analysis
- Tensile and hardness testing
- Dimensional reports to your drawing
- Laser-marked heat codes or part numbers

Questions
Frequently asked questions
Which titanium grade is best for bolts?
Grade 5 (Ti-6Al-4V) is the most common grade for titanium bolts because it is much stronger than the commercially pure grades. Grade 2 is used where corrosion resistance matters more than strength.
Are titanium fasteners good in seawater?
Yes. Titanium fasteners are highly resistant to seawater and chlorides. Titanium is more noble than most metals, so think about galvanic contact with aluminium or carbon steel parts.
What is the difference between titanium Grade 2 and Grade 7?
Grade 7 is essentially Grade 2 with a small palladium addition, which improves its resistance to crevice corrosion.
Can you make titanium fasteners in small quantities?
Yes. We make titanium parts from a single prototype to batches of several hundred.
Useful tools
Free engineering tools
- Material equivalents finder: find the EN, UNS, ASTM, BS and JIS equivalents of a grade, such as 1.4462 or 316.
- Galvanic corrosion checker: check the corrosion risk when joining dissimilar metals.
- Bar weight calculator: weight of round, square and hexagon bar and plate per metre and per piece.
Free to use, no sign-up. See all our engineering tools.
Titanium enquiry?
Send us your drawing or specification
Tell us the grade, sizes, quantity and documentation you need and we will come back to you quickly.
