
Materials · Hastelloy
Hastelloy G30 fasteners
HAGUE FASTENERS makes Hastelloy G30 fasteners to order: bolts, engineer studs and machined parts in Hastelloy G30, the high chromium nickel alloy for phosphoric acid and highly oxidising mixed acids, made to your drawing in Willenhall.
UNS N06030
Also Alloy G30 and Werkstoff 2.4603
28 to 31.5% Cr
High chromium for oxidising acids
765 MPa
Typical tensile strength, solution treated
1 to 500
Prototypes to batches of several hundred
About the alloy
For phosphoric and oxidising acids
HAGUE FASTENERS makes Hastelloy G30 fasteners in the UK, including G30 bolts and engineer studs. G30 is a high chromium nickel-base alloy with better corrosion resistance than most other nickel and iron-base alloys in commercial phosphoric acids and in complex environments with highly oxidising acids, such as nitric with hydrochloric, nitric with hydrofluoric, and sulphuric acids.
We supply G30 fasteners to nuclear fuel and nuclear waste processing, petrochemical bolting, acid service, and fertiliser and pesticide manufacture around the world.
At a glance
- High chromium nickel-base alloy
- For commercial phosphoric acid
- For nitric, hydrofluoric and sulphuric acid mixtures
- Used in nuclear fuel and waste processing
Composition
Hastelloy G30 chemical composition
Percentage by weight. Other elements: V 0.35 max.
| Element | Min % | Max % |
|---|---|---|
| Nickel (Ni) | Bal. | – |
| Chromium (Cr) | 28.0 | 31.5 |
| Molybdenum (Mo) | 4.0 | 6.0 |
| Manganese (Mn) | – | 1.5 |
| Iron (Fe) | 13.0 | 17.0 |
| Silicon (Si) | – | 0.8 |
| Carbon (C) | – | 0.03 |
| Phosphorus (P) | – | 0.04 |
| Sulphur (S) | – | 0.02 |
| Cobalt (Co) | – | 5.0 |
| Tungsten (W) | 1.5 | 4.0 |
Properties
Mechanical properties (typical, solution treated)
Typical values in the solution treated condition.
| Property | Value |
|---|---|
| Tensile strength | 765 MPa |
| Yield strength (0.2% offset) | 317 MPa |
| Elongation in 2 in (50 mm) or 4D | 60% |
This data is for general information only and may change without notice. HAGUE FASTENERS LIMITED believes it to be accurate but gives no warranty as to its accuracy or completeness and accepts no liability for its use. Actual properties may vary, and nothing here guarantees suitability for a particular use.
Equivalents and applications
Hastelloy G30 equivalents and typical uses
Alternative designations
Hastelloy G30, Alloy G30, UNS N06030, Werkstoff 2.4603, ASTM B366, ASTM B581, ASTM B582, ASTM B619, ASTM B622.
Typical applications
- Nuclear fuel and nuclear waste processing
- Phosphoric acid production
- Petrochemical bolting and acid service
- Fertiliser and pesticide manufacture
What we make
Fasteners we make in Hastelloy G30
Certification and testing
Certified, traceable and tested
Bar comes from approved UK, EU or US mills, with heat numbers carried through to release. Testing is by independent UKAS-accredited laboratories, with EN 10204 3.1 or 3.2 certificates as required. See quality and testing.
- Mill certificates and heat traceability
- PMI and chemical analysis
- Solution annealing by approved partners, with furnace charts
- Laser-marked heat codes or part numbers

Questions
Frequently asked questions
What is the equivalent of Hastelloy G30?
Hastelloy G30 is UNS N06030 and Werkstoff 2.4603, also called Alloy G30. Bar is supplied to ASTM B581.
What are Hastelloy G30 fasteners used for?
Hastelloy G30 fasteners are used in phosphoric acid and highly oxidising mixed acid service, including nuclear fuel and waste processing and fertiliser plant.
Can you make Hastelloy G30 fasteners for nuclear plant?
Yes. We release safety-critical parts under First Level QC1 nuclear safety procedures. See nuclear fasteners.
Do you make Hastelloy G30 engineer studs?
Yes. We make G30 engineer studs, stud bolts, bolts and nuts to your drawing or standard.
Hastelloy G30 enquiry?
Send us your drawing or specification
Tell us the sizes, quantity and documentation you need, and we will reply quickly.
