
Materials · Incoloy
A286 fasteners
HAGUE FASTENERS makes A286 fasteners to order: bolts, studs, nuts and screws in Incoloy A286 (UNS S66286), the precipitation hardening iron-nickel-chromium alloy for high temperature bolting, made to your drawing in Willenhall.
A453 660
Also UNS S66286 and W.Nr 1.4980
895 MPa
Minimum tensile strength
700°C
Strength and oxidation resistance up to 1300°F
1 to 500
Prototypes to batches of several hundred
About the alloy
A precipitation hardening alloy for hot bolting
HAGUE FASTENERS makes A286 fasteners in the UK for gas turbines, power plant and other high temperature bolting. A286 is an iron-nickel-chromium alloy with additions of molybdenum and titanium. It is precipitation hardenable for high mechanical properties, and keeps good strength and oxidation resistance at temperatures up to 1300°F (700°C).
The alloy is austenitic in all metallurgical conditions, and is widely used for gas turbine parts and all types of screwed fasteners. We supply it to ASTM A453 grade 660 and the AMS specifications you call up.
At a glance
- Precipitation hardening iron-nickel-chromium alloy
- Strength up to 700°C
- Austenitic in all conditions
- ASTM A453 660, AMS 5732, AMS 5737 and more
Composition
A286 chemical composition
Percentage by weight. Other elements: boron 0.001 to 0.010.
| Element | Min % | Max % |
|---|---|---|
| Nickel (Ni) | 24.00 | 27.00 |
| Molybdenum (Mo) | 1.00 | 1.50 |
| Titanium (Ti) | 1.90 | 2.35 |
| Chromium (Cr) | 13.5 | 16.00 |
| Carbon (C) | – | .08 |
| Silicon (Si) | – | 1.00 |
| Aluminium (Al) | – | .35 |
| Manganese (Mn) | – | 2.0 |
| Phosphorus (P) | – | 0.04 |
| Sulphur (S) | – | .03 |
| Vanadium (V) | .10 | .50 |
Properties
Mechanical properties
Minimum strength, elongation and reduction of area, with the Brinell hardness range.
| Property | Value |
|---|---|
| Tensile strength, min. | 895 MPa |
| Yield strength (0.2% offset), min. | 585 MPa |
| Elongation in 2 in (50 mm) or 4D, min. | 15% |
| Reduction of area, min. | 18% |
| Hardness (Brinell) | 248 to 341 |
This data is for general information only and may change without notice. HAGUE FASTENERS LIMITED believes it to be accurate but gives no warranty as to its accuracy or completeness and accepts no liability for its use. Actual properties may vary, and nothing here guarantees suitability for a particular use.
Equivalents and applications
A286 equivalents and typical uses
Alternative designations
ASTM A453 660, SAE AMS 7235, BS HR 650, ASME SA453 660, S66286, W.Nr 1.4980, ASTM A638, ASME SA638, SAE AMS 5726, SAE AMS 5731, SAE AMS 5732, SAE AMS 5734, SAE AMS 5737, SAE AMS 5895, BS HR 51, BS HR 52, AECMA PrEN2171, AECMA PrEN2119, AECMA PrEN2172, AECMA PrEN2173, AECMA PrEN2174, AECMA PrEN2303, AECMA PrEN2304, AECMA PrEN2398, AECMA PrEN2399, AECMA PrEN3510.
Typical applications
- Aircraft and industrial gas turbine components
- High temperature bolting for turbines and plant
- Blades, vanes, shafts and tail cones
- Springs and all types of screwed fasteners
What we make
Fasteners we make in A286
Certification and testing
Certified, traceable and tested
Bar comes from approved UK, EU or US mills, with heat numbers carried through to release. Testing is by independent UKAS-accredited laboratories, with EN 10204 3.1 or 3.2 certificates as required. See quality and testing.
- Mill certificates and heat traceability
- PMI and chemical analysis
- Solution treatment and ageing by approved partners, with furnace charts
- Laser-marked heat codes or part numbers

Questions
Frequently asked questions
What is the equivalent of A286?
A286 is UNS S66286, W.Nr 1.4980 and ASTM A453 grade 660, with aerospace equivalents including AMS 5732 and AMS 5737.
Can you make A286 fasteners to ASTM A453 grade 660?
Yes. We make A286 fasteners to ASTM A453 grade 660 and ASME SA453 660, with the class and testing your specification requires.
Is A286 magnetic?
No. A286 is austenitic in all metallurgical conditions and is non-magnetic.
What temperature can A286 bolts take?
A286 keeps good strength and oxidation resistance up to 1300°F (700°C). Above that, nickel alloys such as Nimonic 80A or Inconel 718 are often used.
A286 enquiry?
Send us your drawing or specification
Tell us the sizes, quantity and documentation you need, and we will reply quickly.
