Socket set screw made by HAGUE FASTENERS

Materials · Monel

Monel R405 fasteners

HAGUE FASTENERS makes Monel R405 fasteners to order: screws, bolts, nuts and machined parts in Monel R405 (UNS N04405), the free-machining nickel-copper alloy, made to your drawing in Willenhall for seawater, steam and chemical service.

N04405

Free-machining Monel

0.025 to 0.060% S

Controlled sulphur for machining

482 to 586 MPa

Tensile strength range, annealed

1 to 500

Prototypes to batches of several hundred

About the alloy

Monel corrosion resistance, easier to machine

HAGUE FASTENERS makes Monel R405 fasteners in the UK for the chemical, oil and marine industries. R405 is a nickel-copper alloy with excellent corrosion resistance in a wide variety of media, good general corrosion resistance and moderate to high strength. Its controlled sulphur content makes it the free-machining form of Monel 400, well suited to small, detailed turned parts.

It resists seawater, steam at high temperatures, salt and caustic solutions, and rapidly flowing brackish water. It is particularly resistant to de-aerated hydrochloric and hydrofluoric acids.

At a glance

  • Free-machining nickel-copper alloy
  • Resists seawater, steam, salt and caustic solutions
  • Resists de-aerated hydrochloric and hydrofluoric acids
  • Slightly magnetic at room temperature

Composition

Monel R405 chemical composition

Percentage by weight.

ElementMin %Max %
Nickel (Ni)63.00–
Carbon (C)–0.30
Silicon (Si)–0.50
Copper (Cu)28.0034.00
Manganese (Mn)–2.00
Iron (Fe)–2.50
Sulphur (S)0.0250.060
Phosphorus (P)–0.030

Properties

Mechanical properties (annealed)

Typical ranges in the annealed condition. Hardness on the Rockwell B scale.

PropertyValue
Tensile strength482 to 586 MPa
Yield strength (0.2% offset)172 to 275 MPa
Elongation in 2 in (50 mm) or 4D35 to 50%
Hardness60 to 76 HRB

This data is for general information only and may change without notice. HAGUE FASTENERS LIMITED believes it to be accurate but gives no warranty as to its accuracy or completeness and accepts no liability for its use. Actual properties may vary, and nothing here guarantees suitability for a particular use.

Equivalents and applications

Monel R405 equivalents and typical uses

Alternative designations

Monel R-405, Alloy R-405, UNS N04405, ASTM B164, AMS 4674, QQ-N-281.

Typical applications

  • Screws, bolts and turned parts for seawater service
  • Valve and pump components
  • Steam and high temperature water
  • Chemical, oil and marine equipment

What we make

Fasteners we make in Monel R405

Certification and testing

Certified, traceable and tested

Bar comes from approved UK, EU or US mills, with heat numbers carried through to release. Testing is by independent UKAS-accredited laboratories, with EN 10204 3.1 or 3.2 certificates as required. See quality and testing.

  • Mill certificates and heat traceability
  • PMI and chemical analysis
  • Heat treatment by approved partners, with furnace charts
  • Laser-marked heat codes or part numbers
Tensile test of a machined test piece with an extensometer fitted

Questions

Frequently asked questions

What is Monel R405?

Monel R405 is a free-machining version of Monel 400, with controlled sulphur that makes it easier to machine into screws, bolts and small turned parts.

Is Monel R405 magnetic?

Slightly. Monel R405 is slightly magnetic at room temperature.

When should I choose Monel R405 fasteners over Monel 400?

Choose Monel R405 fasteners for small or detailed machined parts where machinability matters. Monel 400 is preferred where the part will be welded or the specification calls for it.

Can you supply Monel R405 with certificates?

Yes. We supply EN 10204 3.1 or 3.2 certificates, with PMI and independent test reports where required.

Monel R405 enquiry?

Send us your drawing or specification

Tell us the sizes, quantity and documentation you need, and we will reply quickly.