Hexagon jam nut machined by HAGUE FASTENERS

Materials · Stainless steels

Nitronic 60 fasteners

HAGUE FASTENERS makes Nitronic 60 fasteners to order: bolts, studs, nuts and machined parts in Nitronic 60 (UNS S21800), made to your drawing from certified, traceable bar, including ASTM A193 B8S bolting. The austenitic stainless steel known for resisting galling and seizing.

96 ksi

Typical tensile strength

50 ksi

Typical yield strength (0.2% offset)

B8S

ASTM A193 bolting grade

UNS S21800

Also AMS 5848

About the alloy

The answer to galling

HAGUE FASTENERS makes Nitronic 60 fasteners in the UK for parts that slide, rub or must come apart again. Nitronic 60 is widely regarded as the best non-galling stainless steel, chosen for high wear applications where galling and seizing are a concern.

Its silicon and manganese additions give galling resistance that standard austenitic grades lack, so threads are far less likely to seize than in 304 or 316. It also outperforms 304 in corrosion resistance and 316/316L in pitting resistance. See all stainless steels.

At a glance

  • Austenitic stainless with silicon and manganese
  • Outstanding resistance to galling and seizing
  • Good wear resistance
  • Better pitting resistance than 316/316L

Chemical composition

Nitronic 60 chemical composition

Weight %.

ElementMin %Max %
Ni8.009.00
Cr16.0018.00
Mn7.009.00
FeBal.–
Si3.504.50
C–0.10
P–0.04
S–0.03
N0.080.18

Mechanical properties

Nitronic 60 mechanical properties

Condition: typical values.

PropertyValue
Tensile strength (ksi)96
Yield strength (0.2% offset) (ksi)50
Elongation in 2 in (50 mm) or 4D (%)35
Reduction of area (%)55
Hardness241 HB max.

These figures are for general information only and may change without notice. We believe them to be accurate, but HAGUE FASTENERS LIMITED gives no warranty and accepts no liability for their accuracy or completeness. Actual properties may vary, and nothing here guarantees the material for a particular use.

Applications

Where Nitronic 60 is used

Nitronic 60 is found in a variety of high wear applications where galling and seizing are a concern, including bridge spacers, internal combustion valves and seats, fasteners, pump components, and pin and roller bearings.

  • Anti-galling bolts, studs and nuts
  • Pump components and wear parts
  • Valves and valve seats
  • Bridge spacers, pins and bearings
Machined tensile test pieces and notched Charpy impact specimens on a test record

Designations

Alternative designations and specifications

AMS 5848 ASTM A193 (B8S, B8SA) ASTM A194 (B8S, B8SA) ASTM A240 ASTM A276 ASTM A479 ASTM A555 ASTM A580 UNS S21800

In bolting specifications, Nitronic 60 appears as ASTM A193 and A194 grades B8S and B8SA.

What we make

Nitronic 60 fasteners and components

Made to your drawing or to the standard you specify.

Certification and testing

Certified, traceable and tested

Nitronic 60 bar comes from approved UK, EU or US mills with heat traceability to release. We supply EN 10204 3.1 or 3.2 certificates, PMI where specified and independent UKAS-accredited testing. See quality and testing.

Questions

Frequently asked questions

Why are Nitronic 60 fasteners used to prevent galling?

Because Nitronic 60 resists galling far better than standard stainless steels. Its silicon and manganese content stops mating threads and surfaces from seizing under load and movement.

Is Nitronic 60 more corrosion resistant than 316?

It outperforms 316/316L in pitting resistance and 304 in general corrosion resistance, while giving much better galling resistance than either.

What is the difference between Nitronic 60 and Nitronic 50?

Nitronic 60 is chosen for galling and wear resistance, while Nitronic 50 is chosen for higher strength and corrosion resistance.

What is the equivalent of Nitronic 60?

Nitronic 60 is also known as UNS S21800 and AMS 5848, and appears in ASTM A193 and A194 as grades B8S and B8SA.

Nitronic 60 enquiry?

Send us your drawing or specification

Tell us the grade, condition, sizes, quantity and paperwork you need.