Collar bolts machined by HAGUE FASTENERS

Materials · Stainless steels

431 stainless steel fasteners

HAGUE FASTENERS makes 431 stainless steel fasteners to order: bolts, studs, nuts and machined parts in 431 stainless steel (UNS S43100), made to your drawing from certified, traceable bar. A martensitic grade with nickel for high strength, toughness and corrosion resistance.

850 to 1000 MPa

Tensile strength

635 MPa

Minimum yield strength (0.2% offset)

248 to 302 BHN

Hardness

UNS S43100

Also AISI 431 and DIN 1.4057

About the alloy

The toughest martensitic stainless

HAGUE FASTENERS makes 431 stainless steel fasteners in the UK for marine, aerospace and general industrial use. Grade 431 is a hardenable martensitic stainless steel that combines excellent impact strength at high hardness with the best corrosion resistance of any martensitic stainless steel.

Its 15 to 18% chromium and 2 to 3% nickel give it more corrosion resistance than 410 while keeping high strength after hardening and tempering. It is magnetic, and a common choice for shafts, bolts and valve parts that need more strength than austenitic grades. See all stainless steels.

At a glance

  • Martensitic chromium-nickel stainless
  • High strength and impact toughness
  • Best corrosion resistance of the martensitic grades
  • Magnetic

Chemical composition

431 stainless steel chemical composition

Weight %.

ElementMin %Max %
C0.120.20
Mn–1.00
Si–1.00
Cr15.0018.00
S–0.03
P–0.04
FeBal.–
Ni2.003.00

Mechanical properties

431 stainless steel mechanical properties

PropertyValue
Tensile strength (MPa)850 to 1000
Yield strength (0.2% offset) (MPa)635 min
Elongation in 2 in (50 mm) or 4D (%)11
Hardness248 to 302 BHN

These figures are for general information only and may change without notice. We believe them to be accurate, but HAGUE FASTENERS LIMITED gives no warranty and accepts no liability for their accuracy or completeness. Actual properties may vary, and nothing here guarantees the material for a particular use.

Applications

Where 431 stainless steel is used

Grade 431 has been used successfully in a variety of aircraft and general industrial applications, including fasteners, bolts, valve components and chemical equipment.

  • High strength bolts and fasteners
  • Valve components
  • Chemical equipment
  • Pump and propeller shafts
  • Aircraft parts
Bars marked with ident, cast and batch number before cutting

Designations

Alternative designations and specifications

AISI 431 AMS 5628 ASTM A276 ASTM A473 ASTM A493 ASTM A511 ASTM A579 ASTM A580 DIN 1.4057 MIL S-18732 MIL S-8967 UNS S43100

What we make

431 stainless steel fasteners and components

Made to your drawing or to the standard you specify.

Certification and testing

Certified, traceable and tested

431 stainless steel bar comes from approved UK, EU or US mills with heat traceability to release. We supply EN 10204 3.1 or 3.2 certificates, PMI where specified and independent UKAS-accredited testing. Heat treatment is by approved partners, with furnace charts on request. See quality and testing.

Questions

Frequently asked questions

What is the difference between 431 and 410 stainless steel?

431 contains more chromium and 2 to 3% nickel, giving better corrosion resistance and toughness than 410 at a similar or higher strength.

Is 431 stainless steel magnetic?

Yes. 431 is a martensitic stainless steel and is magnetic.

Why choose 431 stainless steel fasteners?

For strength and toughness with useful corrosion resistance. 431 stainless steel fasteners are much stronger than annealed 304 or 316, and more corrosion resistant than other martensitic grades.

What is the equivalent of 431 stainless steel?

431 is also known as UNS S43100, AISI 431 and DIN 1.4057.

431 stainless steel enquiry?

Send us your drawing or specification

Tell us the grade, condition, sizes, quantity and paperwork you need.