Socket countersunk screws made by HAGUE FASTENERS

Materials · Titanium

Titanium grade 5 bolts and fasteners

Titanium grade 5 bolts, studs, nuts and screws in Ti-6Al-4V (UNS R56400), made to your drawing in Willenhall where high strength and low weight matter.

Ti-6Al-4V

Also UNS R56400 and Grade 5

896 MPa

Minimum tensile strength

827 MPa

Minimum yield strength

1 to 500

Prototypes to batches of several hundred

About the alloy

High strength with low weight

HAGUE FASTENERS makes titanium grade 5 bolts, studs and nuts in the UK. Grade 5, Ti-6Al-4V, is the most widely used titanium alloy, with about 6% aluminium and 4% vanadium giving far higher strength than commercially pure grades while keeping titanium’s low weight and corrosion resistance.

It is used across aerospace, medical, shipping, military and motorsport work. For the best corrosion resistance at lower strength, see grade 2 or grade 7.

At a glance

  • Alpha-beta titanium alloy, Ti-6Al-4V
  • About half the density of steel
  • High strength to weight ratio
  • ASTM F467 and F468 grade 5

Composition

Titanium grade 5 chemical composition

Percentage by weight.

Element Min % Max %
Titanium (Ti) Bal. –
Carbon (C) – 0.08
Iron (Fe) – 0.25
Nitrogen (N) – 0.05
Oxygen (O) – 0.20
Hydrogen (H) – 0.0125
Aluminium (Al) 5.50 6.75
Vanadium (V) 3.50 4.50

Properties

Mechanical properties

Minimum strength values with typical impact and hardness.

Property Value
Tensile strength 896 MPa min.
Yield strength (0.2% offset) 827 MPa min.
Elongation in 2 in (50 mm) or 4D 10%
Reduction of area 25%
Charpy impact 20 to 27 Joules
Hardness 33 HRC

This data is for general information only and may change without notice. HAGUE FASTENERS LIMITED believes it to be accurate but gives no warranty as to its accuracy or completeness and accepts no liability for its use. Actual properties may vary, and nothing here guarantees suitability for a particular use.

Equivalents and applications

Titanium grade 5 equivalents and typical uses

Alternative designations

Titanium Grade 5, Ti6Al4V, Grade 5, UNS R56400. ASTM B265, B348, B381, B861, F467 and F468; AMS 4911, 4928, 4935, 4965 and 4967; MIL-T-9046 and 9047.

Typical applications

  • Aerospace and defence assemblies
  • Motorsport and performance engineering
  • Marine and offshore equipment
  • Medical and scientific equipment

What we make

Fasteners we make in Titanium grade 5

Certification and testing

Certified, traceable and tested

Bar comes from approved UK, EU or US mills, with heat numbers carried through to release. Testing is by independent UKAS-accredited laboratories, with EN 10204 3.1 or 3.2 certificates as required. See quality and testing.

  • Mill certificates and heat traceability
  • PMI and chemical analysis
  • Ultrasonic and dye penetrant testing where specified
  • Laser-marked heat codes or part numbers
Bar ends laser marked with ident, cast and batch number for traceability

Questions

Frequently asked questions

What is the equivalent of titanium grade 5?

Titanium grade 5 is Ti-6Al-4V and UNS R56400, supplied as bar to ASTM B348 and AMS 4928, among others.

Are titanium grade 5 bolts stronger than stainless steel bolts?

Yes, in most cases. Titanium grade 5 bolts have a minimum tensile strength of 896 MPa, above A4-70 stainless, at roughly half the weight.

Is titanium grade 5 magnetic?

No. Titanium grade 5 is non-magnetic.

Can you make titanium grade 5 bolts to ASTM F468?

Yes. We make grade 5 bolts and studs to ASTM F468 and nuts to ASTM F467, or to your drawing.

Titanium grade 5 enquiry?

Send us your drawing or specification

Tell us the sizes, quantity and documentation you need, and we will reply quickly.