Diamond nuts made by HAGUE FASTENERS

Materials · Titanium

Titanium grade 7 fasteners

HAGUE FASTENERS makes titanium grade 7 fasteners to order: bolts, studs, nuts and washers in titanium grade 7, commercially pure titanium with a small palladium addition, made to your drawing in Willenhall for the harshest chemical duty.

0.12 to 0.25% Pd

Palladium for corrosion resistance

345 MPa

Minimum tensile strength

F467 / F468

ASTM nut and bolt standards, Gr7

1 to 500

Prototypes to batches of several hundred

About the alloy

Grade 2 strength with palladium for corrosion resistance

HAGUE FASTENERS makes titanium grade 7 fasteners in the UK for chemical process and other severe corrosion duty. Grade 7 is a commercially pure titanium very similar to grade 2, with a small addition of palladium that improves its resistance to reducing acids and to crevice corrosion.

Its mechanical properties match grade 2, so it is chosen where corrosion, not strength, decides the material. Like all titanium, it combines low weight with high corrosion resistance.

At a glance

  • Commercially pure titanium with palladium
  • Mechanical properties as grade 2
  • For reducing acids and crevice corrosion
  • ASTM F467 and F468 Gr7

Composition

Titanium grade 7 chemical composition

Percentage by weight.

Element Min % Max %
Titanium (Ti) Bal. –
Carbon (C) – 0.10
Iron (Fe) – 0.30
Nitrogen (N) – 0.03
Oxygen (O) – 0.25
Hydrogen (H) – 0.0125
Palladium (Pd) 0.12 0.25

Properties

Mechanical properties

Minimum strength values with typical impact and hardness.

Property Value
Tensile strength 345 MPa min.
Yield strength (0.2% offset) 276 MPa min.
Elongation in 2 in (50 mm) or 4D 20%
Reduction of area 30%
Charpy impact 40 to 82 Joules
Hardness 82 HRB

This data is for general information only and may change without notice. HAGUE FASTENERS LIMITED believes it to be accurate but gives no warranty as to its accuracy or completeness and accepts no liability for its use. Actual properties may vary, and nothing here guarantees suitability for a particular use.

Equivalents and applications

Titanium grade 7 equivalents and typical uses

Alternative designations

ASTM B265 Gr7, ASTM B337 Gr7, ASTM B338 Gr7, ASTM B348 Gr7, ASTM B367 Gr7, ASTM B381 Gr7, ASTM F467 Gr7, ASTM F468 Gr7.

Typical applications

  • Chemical process plant with reducing acids
  • Hot chloride and brine service
  • Equipment prone to crevice corrosion
  • Where grade 2 is not resistant enough

What we make

Fasteners we make in Titanium grade 7

Certification and testing

Certified, traceable and tested

Bar comes from approved UK, EU or US mills, with heat numbers carried through to release. Testing is by independent UKAS-accredited laboratories, with EN 10204 3.1 or 3.2 certificates as required. See quality and testing.

  • Mill certificates and heat traceability
  • PMI and chemical analysis
  • Ultrasonic and dye penetrant testing where specified
  • Laser-marked heat codes or part numbers
Bar ends laser marked with ident, cast and batch number for traceability

Questions

Frequently asked questions

What is the difference between titanium grade 2 and grade 7?

Grade 7 is grade 2 with 0.12 to 0.25% palladium added, which improves corrosion resistance while keeping the same mechanical properties.

Can you make titanium grade 7 fasteners to ASTM F467 and F468?

Yes. We make titanium grade 7 fasteners as bolts and studs to ASTM F468 Gr7 and nuts to ASTM F467 Gr7.

Is titanium grade 7 magnetic?

No. Titanium is non-magnetic.

When is titanium grade 7 used?

When grade 2 titanium is not resistant enough, for example in reducing acids or where crevice corrosion is a risk in chemical plant.

Titanium grade 7 enquiry?

Send us your drawing or specification

Tell us the sizes, quantity and documentation you need, and we will reply quickly.