Hexagon flange bolts made by HAGUE FASTENERS

Materials · Duplex

Super duplex S32750 bolts and studs

Super duplex S32750 bolts, stud bolts, nuts and machined parts in F53, 1.4410 and SAF 2507, made to your drawing in Willenhall for seawater, subsea and offshore service.

F53

Also UNS S32750, 1.4410 and SAF 2507

550 MPa

Minimum yield strength

PREN ≥ 40

Pitting resistance for seawater

1 to 500

Prototypes to batches of several hundred

About the alloy

Built for seawater and chlorides

HAGUE FASTENERS makes super duplex S32750 bolts, studs and nuts in the UK for offshore, subsea, desalination and chemical plant. S32750 (F53, 1.4410, SAF 2507) has excellent corrosion resistance to a wide variety of media, with outstanding resistance to pitting and crevice corrosion in seawater and other chloride environments, and a critical pitting temperature above 50°C.

Its 25% chromium super duplex structure combines this with high strength, so bolting can be lighter than in austenitic stainless. It is listed in NACE MR-01-75 for oil and gas service. See also S32760, its close relative with copper and tungsten.

At a glance

  • 25% chromium super duplex stainless steel
  • Critical pitting temperature above 50°C
  • PREN 40 or more
  • Listed in NACE MR-01-75

Composition

Super duplex S32750 chemical composition

Percentage by weight. PREN = [Cr %] + 3.3 [Mo %] + 16 [N %] ≥ 40.

ElementMin %Max %
Carbon (C)–0.030
Manganese (Mn)–1.20
Phosphorus (P)–0.035
Sulphur (S)–0.020
Silicon (Si)–0.80
Chromium (Cr)24.0026.00
Nickel (Ni)6.008.00
Molybdenum (Mo)3.005.00
Nitrogen (N)0.240.32
Copper (Cu)–0.50

Properties

Mechanical properties

Tensile range and minimum yield and elongation.

PropertyValue
Tensile strength760 to 930 MPa
Yield strength (0.2% offset)550 MPa min.
Elongation in 2 in (50 mm) or 4D, min.25%
Hardness260 HB approx

This data is for general information only and may change without notice. HAGUE FASTENERS LIMITED believes it to be accurate but gives no warranty as to its accuracy or completeness and accepts no liability for its use. Actual properties may vary, and nothing here guarantees suitability for a particular use.

Equivalents and applications

Super duplex S32750 equivalents and typical uses

Alternative designations

UNS S32750, EN 1.4410, EN X2CrNiMoN25-7-4, F53 (ASTM A182 / A479), Sandvik SAF 2507. Listed in NACE MR-01-75 for oil and gas service.

Typical applications

  • Offshore and subsea bolting
  • Seawater pumps, valves and pipework
  • Desalination plant
  • Chemical process equipment in chloride service

What we make

Fasteners we make in Super duplex S32750

Certification and testing

Certified, traceable and tested

Bar comes from approved UK, EU or US mills, with heat numbers carried through to release. Testing is by independent UKAS-accredited laboratories, with EN 10204 3.1 or 3.2 certificates as required. See quality and testing.

  • Mill certificates and heat traceability
  • PMI and chemical analysis
  • Solution annealing by approved partners, with furnace charts
  • Laser-marked heat codes or part numbers
Machined tensile test pieces and notched Charpy impact specimens on a test record

Questions

Frequently asked questions

What is the equivalent of super duplex S32750?

Super duplex S32750 is F53, EN 1.4410, X2CrNiMoN25-7-4 and Sandvik SAF 2507.

Are super duplex S32750 bolts suitable for seawater?

Yes. Super duplex S32750 bolts resist pitting and crevice corrosion in seawater, with a critical pitting temperature above 50°C, which is why they are used offshore and subsea.

What is the difference between S32750 and S32760?

Both are 25% chromium super duplex steels with PREN of 40 or more. S32760 adds copper and tungsten, and is often supplied as Zeron 100.

Is super duplex magnetic?

Yes. Super duplex contains ferrite and is magnetic.

Super duplex S32750 enquiry?

Send us your drawing or specification

Tell us the sizes, quantity and documentation you need, and we will reply quickly.