Tools

Bolt and Nut Compatibility Checker: Which Nut for My Bolt

This free bolt and nut matching checker from HAGUE FASTENERS LIMITED checks bolt and nut compatibility. It tells you which nut and washer go with a bolt or stud grade, and why. Choose the bolt or stud, such as ASTM A193 B7, B8M Class 2, ISO 10.9 or A4-80, and it gives the recommended nut, any acceptable alternatives and the washer. You can also check a nut you already have.

Bolt and nut matching checker

Pairings from ASTM A193, A194, A320, A453 and A563, ISO 898-1 and 898-2, ISO 3506 and SAE J429 and J995. Your project specification, piping class or drawing always takes priority. Sour service, low temperature and high temperature duties may need extra testing or hardness limits on both studs and nuts.

Ask us about special bolting

Guidance only. Results are approximate and for initial guidance. They are not a substitute for the governing standard, specification or drawing, or for testing. HAGUE FASTENERS LIMITED accepts no liability for decisions made using these tools. Always check critical values against the relevant standard. © 2026 HAGUE FASTENERS LIMITED.

How to use the matching checker

  1. Choose the bolt or stud grade from the list.
  2. Read the recommended nut, the acceptable alternatives and the washer.
  3. To check a nut you already have, pick it in the second box. The checker tells you whether it is the correct pairing, acceptable or not recommended.

Why the nut matters

A nut must be at least as strong as the bolt, or its thread can strip before the bolt reaches its full strength. For sour service the nut needs the same hardness limit as the stud, for low temperature it needs impact testing, and for high temperature it must keep its strength. Stainless and nickel alloy studs normally take nuts in the same material, so the joint has the same corrosion resistance throughout.

Nut markings help here. ASTM A194 nuts are stamped with their grade, such as 2H, 4, 7 or 8M, and ISO 898-2 nuts with their property class, such as 8, 10 or 12, so you can compare a nut you already have with the result above. If a nut has no marking, or you are not sure what it is, treat it as unknown and replace it with a certified nut.

Frequently asked questions

Which nut goes with a B7 stud?

ASTM A194 Grade 2H is the standard nut for A193 B7 studs. Grade 4 and Grade 7 nuts are stronger and may also be used.

Can I use a 2H nut on a B7M stud?

Not for sour service. B7M studs are hardness limited for sour service, and the nut must be too, so use A194 2HM or 7M.

Which nut goes with a B8M stud?

ASTM A194 Grade 8M, which is the same 316 type stainless steel as the stud, so the joint has the same corrosion resistance throughout.

Which nut goes with an L7 stud for low temperature service?

ASTM A194 Grade 7 nuts, impact tested to suit the design temperature. Grade 4 nuts are an acceptable alternative where your specification allows.

Which nut goes with a 10.9 bolt?

An ISO 898-2 property class 10 nut, with hardened 300 HV washers. A class 8 nut can strip before a 10.9 bolt reaches its strength.

Which nut goes with an A4-80 bolt?

An A4-80 nut to ISO 3506-2. An A4-70 nut is weaker than the bolt, so it is not the right match where the joint needs the full strength of the bolt.

Which nut do I use with duplex, Inconel or titanium studs?

Normally a nut in the same material, so the joint has the same strength and corrosion resistance. These alloys can gall (seize) as they are tightened, so use a suitable thread lubricant or anti-seize compound.

Does the checker replace my specification?

No. The project specification, piping class or drawing always takes priority. HAGUE FASTENERS LIMITED makes studs, bolts and nuts to the grade and specification you require, with full material certification.

More engineering tools

Need special studs, bolts or nuts made? Specify your fastener and send an enquiry, or call +44 (0)1902 365 865.

Talk to us

Send us the difficult ones.