Tools

Flange Bolt Chart and Bolting Finder

This free flange bolting finder and flange bolt chart from HAGUE FASTENERS LIMITED gives the number, size and length of stud bolts and nuts for ASME B16.5 pipe flanges, NPS 1/2 to 24, Class 150 to 2500, with raised face or ring type joint facings.

Choose the class and size, add tensioning if you use it, and it works out the studs and nuts for as many joints as you need.

Flange bolting finder (ASME B16.5)

Anything special?

Stud counts, diameters and lengths from ASME B16.5 for NPS 1/2 to 24, Class 150 to 2500. Lengths are measured from first thread to first thread, without the points, and allow for a standard gasket and the raised face (1/16" on Class 150 and 300, 1/4" on Class 600 and above). Allow extra length for thick or insulating gasket kits, spacers, orifice flanges, wafer valves and tensioning. Studs up to 1" are UNC; 1 1/8" and above are 8 UN. Nuts are heavy hex to ASME B18.2.2.

Guidance only. Results are approximate and for initial guidance. They are not a substitute for the governing standard, specification or drawing, or for testing. HAGUE FASTENERS LIMITED accepts no liability for decisions made using these tools. Always check critical values against the relevant standard. © 2026 HAGUE FASTENERS LIMITED.

How to use the flange bolting finder

  1. Choose the pressure class and the flange size (NPS).
  2. Choose raised face (RF) or ring type joint (RTJ).
  3. Enter the number of joints to get the total studs and nuts.
  4. Choose the bolting material and coating.
  5. Tick anything special, such as bolt tensioning, which adds length, or 3.2 certification.

Standard B7 and B16 flange studs

Standard ASTM A193 B7 studs with A194 2H nuts, and standard B16 studs, are stock items. Stockists and distributors in the UK, Europe and worldwide hold them in every common size, and they can usually supply faster and at a lower price than a manufacturer. For standard flange bolting in these grades we suggest you use a stockist.

Where HAGUE FASTENERS can help

  • Exotic and high performance grades: duplex and super duplex, Inconel 625 and 718, Monel K500, B8M Class 2, L7 and B7M for sour service.
  • Tensioning studs and other non-standard lengths, threads and ends.
  • Special coatings, and testing such as impact, hardness, PMI and NDT.
  • EN 10204 3.2 certification, nuclear release and defence work.
  • Breakdowns and shutdowns that cannot wait for a mill run or an overseas shipment.

Frequently asked questions

Why are ring type joint studs longer?

A ring joint flange is held apart by the metal ring gasket sitting in its grooves, so the gap between the flanges is larger than with a raised face and a spiral wound gasket. ASME B16.5 lists a separate, longer stud length for ring joint flanges in most sizes.

How much longer should studs be for bolt tensioning?

Hydraulic bolt tensioners grip the thread above the nut, so the stud needs extra length on the tool end. One stud diameter is a common allowance, and the finder adds this and rounds up to the next 1/4 inch. Always check the length your tensioning tool supplier asks for.

Which nuts go with which studs?

The usual pairings are B7 studs with 2H nuts, B7M with 2HM, L7 with grade 7 nuts, B16 with grade 4 or 7, and B8M Class 2 with 8M nuts. Exotic grades normally use nuts in the same material. Our bolt torque calculator works out the tightening torque once you have the size.

What does ASME B16.5 cover?

ASME B16.5 covers steel pipe flanges and flanged fittings from NPS 1/2 to NPS 24, in pressure classes 150, 300, 400, 600, 900, 1500 and 2500, including the number and size of bolts for each flange.

Can you make flange studs in duplex, Inconel or other special grades?

Yes. Flange studs and nuts in duplex and super duplex, Inconel 625 and 718, Monel K500, B8M Class 2, L7 and B7M are regular work, made to the grade and specification you require with EN 10204 3.1 or 3.2 certificates.

More engineering tools

Need special flange studs made? Specify your fastener and send an enquiry, or call +44 (0)1902 365 865.

Talk to us

Send us the difficult ones.